Chevrolet Sonic 2012 Скачать руководство пользователя страница 626

Страница: 626 / 812

Callout

Component Name

Preliminary Procedures

1. Remove the driver or passenger seat. Refer to

Driver or Passenger Seat Replacement

2. Remove the front seat cushion outer trim panel. Refer to

Front Seat Cushion Outer Trim Panel Replacement

3. Remove the front seat cushion inner recliner. Refer to

Front Seat Cushion Inner Trim Panel Replacement

Front Seat Back Cushion Frame Bolt (Qty:

Caution:

Refer to

Fastener Caution

Tighten

N·m(16

ft)

Driver or Passenger Seat Back Cushion Frame

Procedure

1. Disconnect electrical connectors as needed.

2. If replacing with a new front seat back cushion frame, transfer components as necessary.

Driver or Passenger Seat Back Cushion Frame Replacement

Seats

SEATS

0-7

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды