Chevrolet Sonic 2012 Скачать руководство пользователя страница 607

Страница: 607 / 812

Callout

Component Name

Warning:

Refer to

SIR Warning

Preliminary Procedures

1. Disable the SIR system. Refer to

SIR Disabling and Enabling

2. Disconnect the front seat belt lower fastener. Refer to

Driver or Passenger Seat Shoulder Belt Replacement

3. Disable the front seat belt tensioner fastener by removing the cap, and cover, if equipped. Refer to

SIR Disabling and

Enabling

Front Seat Riser Finish Cover (Qty:

Procedure

Remove the front seat riser cover. Refer to

Front Seat Riser Finish Cover Replacement

Front Seat Mounting Bolt (Qty:

Caution:

Refer to

Fastener Caution

Procedure

Adjust the seat to the full forward position to gain access to the rear bolts.

Tighten

N·m (30

ft)

Driver or Passenger Seat Assembly (Qty:

Procedure

1. Disconnect the electrical.
2. With the aid of an assistant remove the front seat, by tilting the seat forward and then lifting and pulling the

seat rearwards to disengage the front hooks.
3. Transfer components as necessary.

Driver or Passenger Seat Replacement

Seats

SEATS

0-7

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды