Chevrolet Sonic 2012 Скачать руководство пользователя страница 159

Страница: 159 / 812

Callout

Component Name

Preliminary Procedure

Remove the instrument panel lower compartment. Refer to

Instrument Panel Lower Compartment Replacement

Instrument Panel Compartment Door Dampener

Procedure

Unsnap the dampener assembly from the instrument panel compartment housing.

Instrument Panel Compartment Door Dampener Replacement

Instrument Panel and Console Trim

BODY HARDWARE AND TRIM

0-2

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды