Chevrolet Sonic 2012 Скачать руководство пользователя страница 465

Страница: 465 / 812

Brake Pedal Position Sensor Replacement

Removal Procedure

1. Remove the instrument panel lower trim pad cover. Refer to

Instrument Panel Lower Trim Pad Cover Replacement

2. Disconnect the brake pedal position sensor electrical connector.
3. Remove the brake pedal position sensor bolt

(1).

4. Remove the brake pedal position sensor.

Installation Procedure

Note: Ensure the fork of the brake pedal position sensor is positioned over the brake pedal post.

1. Install the brake pedal position sensor to the brake pedal bracket.

Caution:

Refer to

Fastener Caution

2. Install the brake pedal position sensor bolt

(1)

and tighten to

N·m (27

in).

3. Connect the brake pedal position sensor electrical connector.
4. Calibrate the brake pedal position sensor. Refer to

Brake Pedal Position Sensor Calibration

5. Install the instrument panel lower trim pad cover. Refer to

Instrument Panel Lower Trim Pad Cover Replacement

Lighting

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды