Chevrolet Sonic 2012 Скачать руководство пользователя страница 336

Страница: 336 / 812

6. Position the quarter outer panel on the vehicle (1).
7. Verify the fit of the quarter outer panel.
8. Clamp the quarter outer panel into position.

9. Plug weld accordingly (1).
10. To create a solid weld with minimum heat distortion, make 25

mm (1

in)stitch welds along the seam with 25

mm (1

in)gaps

between them. Then go back and complete the stitch weld.

11. Pre-flange the flange with BO-6396 pliers and BO-6392 tool kit.

12. Finish closing the wheelhouse flanging.
13. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to

Anti-Corrosion Treatment and

Repair

14. Paint the repaired area. Refer to

Basecoat/Clearcoat Paint Systems

15. Install all related panels and components.
16. Connect the negative battery cable. Refer to

Battery Negative Cable Disconnection and Connection

17. Enable the SIR system. Refer to

SIR Disabling and Enabling

Collision Repair

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды