Chevrolet Sonic 2012 Скачать руководство пользователя страница 433

Страница: 433 / 812

Callout

Component Name

Preliminary Procedures

1. The rear door side window weatherstrip and window is serviced as one assembly. Refer to

Rear Side Door Stationary

Window Replacement

2. Remove the rear side door window . Refer to

Rear Side Door Window Replacement

Rear Side Door Window Weatherstrip Lower Bolt

Caution:

Refer to

Fastener Caution

Procedure

Remove the rear side door water deflector.

Tighten

N·m (80

in)

Rear Side Door Window Weatherstrip Upper Screw

Procedure

1. Pull the door weatherstrip out of the upper retainer to expose the screw.
2. Remove the weatherstrip from the front and rear lower guides.

3. Grasp both upper corners, pull downward releasing the weatherstrip from the door frame.

Tighten

N·m (27

in)

Rear Side Door Window Weatherstrip

Procedure

1. Insert the weatherstrip downward in the guide until fully seated.

2. Carefully move the regulator upward for short slow intervals, while ensuring that the window remains in the
guides.

Rear Side Door Window Weatherstrip Replacement (Sedan)

3. Inspect the door window for proper operation before installing the door trim panel.

Fixed and Movable Windows

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды