Chevrolet Sonic 2012 Скачать руководство пользователя страница 727

Страница: 727 / 812

6. Remove the front suspension strut mount

(1), front spring insulator

(2), front spring

(3), front suspension strut bumper

(4),

and the front strut

(5)

from the spring compressor.

Assembly Procedure

1. Install the front suspension strut

(5), front suspension strut bumper

(4), front spring

(3), front spring insulator

(2), and the

front suspension strut mount

(1)

in the spring compressor.

Front Suspension

SUSPENSION

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды