Chevrolet Sonic 2012 Скачать руководство пользователя страница 671 | Manualshive

Страница: 671 / 812

background image

Callout

Component Name

Warning:

Refer to

SIR Warning

.

Warning:

Refer to

SIR Seatbelt Pretensioner Handling Warning

.

Warning: In order to prevent accidental deployment and the risk of personal injury, do not dispose of an undeployed
inflatable restraint seat belt pretensioner as normal shop waste. Undeployed seat belt pretensioners contain

substances that could cause severe illness or personal injury if their sealed containers are damaged during disposal.
Use the following deployment procedures to safely dispose of an undeployed seat belt pretensioner. Failure to

observe the following disposal methods may be a violation of federal, state, or local laws.

Preliminary Procedures

1. Remove the center pillar upper trim panel. Refer to

Center Pillar Upper Trim Panel Replacement

.

2. Remove the front seat lower finish cover. Refer to

Front Seat Belt Anchor Plate Tensioner Cover Replacement

.

1

Front Seat Belt Anchor Plate Fastener

Caution:

Refer to

Fastener Caution

.

Tighten

8

N·m

(70

lb

in)

2

Front Seat Belt Retractor D Ring Fastener

Tighten

45

N·m

(33

lb

ft)

3

Front Seat Shoulder Belt Guide Retainer

4

Front Seat Shoulder Belt Retractor Fastener

Tighten

45

N·m

(33

lb

ft)

Driver or Passenger Seat Shoulder Belt Replacement (without A69)

© 2011 General Motors. All rights reserved.

5

Front Seat Shoulder Belt Assembly

Restraints

RESTRAINTS

0-8

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
669
670
671
672
673
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: Suzuki Страницы: 16

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Бренд: Cadillac Страницы: 20

Бренд: Great Wall Страницы: 18

Бренд: WIX Страницы: 2

1506-PHX Cargo Plus

Бренд: Ranger design Страницы: 8

Бренд: AUTOTECH Страницы: 1

Бренд: Radical Sportscars Страницы: 44

Бренд: DriveRight Страницы: 16

ZapCharger Portable C1

Бренд: ZAPTEC Страницы: 20

Бренд: Oldsmobile Страницы: 380

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды