Chevrolet Sonic 2012 Скачать руководство пользователя страница 208

Страница: 208 / 812

Callout

Component Name

Preliminary Procedures

1. Remove the rear compartment lid outer bumpers.
2. Remove the latch cover.

Rear Compartment Lid Inner Panel Trim Retainer (Qty:

13)

Procedure

Use a trim removal tool to aid in the removal of the rear compartment trim panel.

Rear Compartment Lid Inner Panel Trim

Rear Compartment Lid Inner Panel Trim Replacement (Sedan)

0-2

InteriorTrim

BODY HARDWARE AND TRIM

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды