Chevrolet Sonic 2012 Скачать руководство пользователя страница 710

Страница: 710 / 812

Callout

Component Name

Preliminary Procedure

1. Raise and Support the vehicle. Refer to

Lifting and Jacking the Vehicle

2. Remove the tire and wheel assembly. Refer to

Tire and Wheel Removal and Installation

Front Stabilizer Shaft Link Upper Nut

Caution:

Refer to

Fastener Caution

Procedure

1. Use the proper size Allen wrench to hold the stabilizer shaft link stud when loosening or tightening the
stabilizer shaft link nut.

2. Remove and discard the stabilizer shaft link nut. Replace with NEW only.

Tighten

N·m (48

ft)

Front Stabilizer Shaft Link Lower Nut

Procedure

1. Use the proper size Allen wrench to hold the stabilizer shaft link stud when loosening or tightening the
stabilizer shaft link nut.

2. Remove and discard the nut. Replace with NEW only.

Tighten

N·m (48

ft)

Front Stabilizer Shaft Link

Stabilizer Shaft Link Replacement

Front Suspension

SUSPENSION

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды