Chevrolet Sonic 2012 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 812

background image

Callout

Component Name

Preliminary Procedures

1. Remove the front bumper fascia assembly. Refer to

Front Bumper Fascia Replacement

.

2. Remove the front bumper fascia energy absorber. Refer to

Front Bumper Energy Absorber Replacement

.

1

Radiator Lower Front Grille

Procedure

1. Release the four upper tabs from the front bumper fascia.

2. Release the two outer center tabs from the front bumper fascia.
3. Release the four lower tabs from the front bumper fascia.

4. Push the lower grille assembly outward, from the front bumper fascia in order to remove.
5. Upon installation, index the right center alignment pin to the front bumper fascia first, followed by the ten

locking tabs on the lower grille assembly to the front bumper fascia.
6. Push the locking tabs inward at all ten locations, in order to secure the radiator lower front grille to the front

bumper fascia.

2

Front License Plate Bracket Assembly

Procedure

Remove the four screws and the front license plate bracket to transfer to the new lower front grille assembly, (if

equipped).

Radiator Lower Grille Replacement

© 2011 General Motors. All rights reserved.

0-2

Exterior Trim

BODY HARDWARE AND TRIM

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
120
121
122
123
124
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: RaceChip Страницы: 20

Бренд: Toyota Страницы: 35

Бренд: MAXWORKS Страницы: 7

Бренд: AA Products Страницы: 4

Бренд: Kuda Страницы: 3

Бренд: Honda Страницы: 20

2009 Rio Series

Бренд: Kia Страницы: 219

Бренд: Unex Страницы: 30

Бренд: Linear Logic Страницы: 8

Бренд: Thule Страницы: 4

Бренд: Husky Страницы: 8

Бренд: Opel Страницы: 242

Бренд: Metra Electronics Страницы: 8

Бренд: Pet Gear Страницы: 4

Бренд: Havis Страницы: 4

Бренд: iDataLink Страницы: 11

Hyper Car Charger 30W

Бренд: 3mk Страницы: 6

2001 MR2 Spyder

Бренд: Toyota Страницы: 234

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды