Chevrolet Sonic 2012 Скачать руководство пользователя страница 237

Страница: 237 / 812

Callout

Component Name

Preliminary Procedure

Remove the front side door trim panel. Refer to

Front Side Door Trim Replacement

Front Side Door Check Link Bolt to Body

Caution:

Refer to

Fastener Caution

Note: Place the door window in the full open position.

Tighten

N·m (16

ft)

Front Side Door Check Link Nut (Qty:

Procedure

Remove the water deflector.

Tighten

N·m (80

in)

Front Side Door Check Link

Front Side Door Check Link Replacement

Bolted Exterior Body Panels and Closures

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды