Chevrolet Sonic 2012 Скачать руководство пользователя страница 565

Страница: 565 / 812

Callout

Component Name

Preliminary Procedure

1. Remove both wiper arm assemblies. Refer to

Windshield Wiper Arm Replacement

2. Remove both outer hood rear seals. Refer to

Hood Rear Seal Replacement

Air Inlet Grille Panel Retainer (Qty:

Procedure

Release and remove the retainers from the air inlet grille panel.

Air Inlet Panel Screw

Caution:

Refer to

Fastener Caution

Procedure

1. Remove the screw cover from the air inlet grille panel.

2. Remove the air inlet grille panel screw. Tighten

2.5

N·m (22

in)

Air Inlet Grille Panel

Procedure

1. Lift the front edge of the grille panel off the front edge of the dash upper extension panel opening cover.

2. Slide the grille panel forward from both hood hinges.
3. Remove the grille panel from the vehicle.

4. Remove the hood rear weather-strip. Refer to

Hood Rear Weatherstrip Replacement

Air Inlet Grille Panel Replacement

Wipers and Washers

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды