Chevrolet Sonic 2012 Скачать руководство пользователя страница 654 | Manualshive

Страница: 654 / 812

background image

• Passenger presence module and/or occupant sensor

Disabling Procedure – Air Bag Fuse

1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
2. Place the ignition in the OFF position.

Warning: The SDM may have more than one fused power input. To ensure there is no unwanted SIR deployment, personal

injury, or unnecessary SIR system repairs, remove all fuses supplying power to the SDM. With all SDM fuses removed and the
ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate a

SIR system malfunction.

3. Locate and remove the fuse(s) supplying power to the SDM. Refer to

SIR Schematics

or

Electrical Center Identification Views

.

4. Wait 1 minute before working on the system.

Enabling Procedure – Air Bag Fuse

1. Place the ignition in the OFF position.
2. Install the fuse(s) supplying power to the SDM. Refer to

SIR Schematics

or

Electrical Center Identification Views

.

3. Turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
4. Perform the Diagnostic System Check – Vehicle if the AIR BAG warning indicator does not operate as described. Refer to

Diagnostic System Check - Vehicle

.

Disabling Procedure – Negative Battery Cable

1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
2. Place the ignition in the OFF position.
3. Disconnect the negative battery cable from the battery. Refer to

Battery Negative Cable Disconnection and Connection

.

4. Wait 1 minute before working on system.

Enabling Procedure – Negative Battery Cable

1. Place the ignition in the OFF position.
2. Connect the negative battery cable to the battery. Refer to

Battery Negative Cable Disconnection and Connection

.

3. Turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
4. Perform the Diagnostic System Check – Vehicle if the AIR BAG warning indicator does not operate as described. Refer to

Diagnostic System Check - Vehicle

.

© 2011 General Motors. All rights reserved.

Restraints

RESTRAINTS

0-8

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
652
653
654
655
656
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: Fabbri Страницы: 4

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: APEXi Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Sirius Satellite Radio Страницы: 8

MAGNUM RT Series

Бренд: Raptor Series Страницы: 6

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: Hummer Страницы: 502

Бренд: Icom Страницы: 20

2011 A3 Sportback

Бренд: Audi Страницы: 29

Бренд: CrimeStopper Страницы: 1

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

Bluetooth Kit3 PLUS

Бренд: N-Com Страницы: 36

Бренд: Yakima Страницы: 12

Бренд: NavLinkz Страницы: 26

Бренд: Kargo Master Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды