Chevrolet Sonic 2012 Скачать руководство пользователя страница 377

Страница: 377 / 812

6. Install the upper frame suspension retaining bolts

(1) and tighten to 135

N·m (100

ft)

7. Remove the support for the power steering gear.

8. Install the steering gear retaining fasteners

(1). Refer to

Steering Gear Boot Replacement

9. Connect the hydraulic power steering hoses to the front frame, if equipped.
10. Connect the exhaust isolators

(2) to the front suspension frame.

11. Install the rear transmission mount bracket to rear mount through bolt

(1). Refer to

Transmission Rear Mount Replacement .

12. Connect the power brake booster pump hose and connector, if equipped.
13. Connect the lower ball joints to the steering knuckles. Refer to

Lower Control Arm Replacement

14. Connect the stabilizer links to the strut assemblies. Refer to

Stabilizer Shaft Link Replacement

15. Connect the steering linkage tie rod end to the steering knuckle. Refer to

Steering Linkage Outer Tie Rod Replacement

16. Install the front bumper impact bar lower bracket. Refer to

Front Bumper Impact Bar Lower Bracket Replacement

17. Install the left and right front wheel house liner inner front extensions. Refer to

Front Wheelhouse Liner Inner Front

Extension Replacement

18. Install the skid plate to the front frame, if equipped. Refer to

Drivetrain and Front Suspension Frame Skid Plate

Replacement

19. Install the front tire and wheel assembly. Refer to

Tire and Wheel Removal and Installation

20. Lower the vehicle.
21. Remove the support of the radiator and condenser.

Frame and Underbody

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды