Chevrolet Sonic 2012 Скачать руководство пользователя страница 633

Страница: 633 / 812

Callout

Component Name

Rear Seat Center Head Restraint

Procedure

1. Depress the large button on the head restraint guide and raise the head restraint to the full up position.

2. Depress the small button on the opposite head restraint guide and pull upward to remove from the seat.

Rear Seat Center Head Restraint Replacement

Seats

SEATS

0-7

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды