Chevrolet Sonic 2012 Скачать руководство пользователя страница 736

Страница: 736 / 812

Callout

Component Name

Preliminary Procedure

Raise and support the vehicle. Refer to

Lifting and Jacking the Vehicle

Rear Spring

Procedure

1. If removing the rear spring to service other suspension components, note the position of the rear spring in
relationship to the insulators.

2. Support the rear axle with a hydraulic jack.
3. Remove the lower rear shock absorber bolt. Refer to

Shock Absorber Replacement

Upper Rear Spring Insulator

Tip

Ensure that the rear spring insulator is properly seated in the rear frame rail.

Lower Rear Spring Insulator

Tip
Ensure that the rear spring insulator is properly seated in the rear axle.

Rear Spring, Insulator, and Jounce Bumper Replacement

Rear Suspension

SUSPENSION

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды