Chevrolet Sonic 2012 Скачать руководство пользователя страница 23

Страница: 23 / 812

Radiator Cap Removal Warning

Warning: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling

system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and
radiator are still hot.

0-0

Caution Notices

PREFACE

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды