Chevrolet Sonic 2012 Скачать руководство пользователя страница 415

Страница: 415 / 812

Note: Keep the cutting edge of appropriate tool the against the window. Do this from inside the vehicle.

8. Use the appropraite tool to remove the bottom of the window from the auto-adhesive. Keep the cutting edge of the tool

against the window. Do this from inside the vehicle.

9. With an assistant, remove the window

(1) from the vehicle.

Installation Procedure

1. Install the liftgate window into the opening. Refer to

Adhesive Installation of Liftgate Windows

2. Install the rear spoiler. Refer to

Rear End Spoiler Replacement

3. Install the rear window wiper arm. Refer to

Rear Window Wiper Arm Replacement

4. Connect the liftgate window defogger electrical connectors to the bus bar.
5. Install the liftgate trim. Refer to

Liftgate Trim Finish Panel Replacement

6. Remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim.
7. Close the liftgate.

Fixed and Movable Windows

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды