Chevrolet Sonic 2012 Скачать руководство пользователя страница 497

Страница: 497 / 812

Callout

Component Name

Preliminary Procedure

Remove the tail lamp assembly. Refer to

Tail Lamp Replacement

Tail Lamp Socket (Qty:

Procedure

Rotate the lamp socket counter-clockwise and remove the socket from the lamp housing.

Park and Stop Lamp Bulb

Procedure

Pull the bulb straight from the lamp harness socket.

Turn Signal Bulb

Back Up Bulb

Tail Lamp Housing Assembly

Stop and Turn Signal Lamp Bulb Replacement (Hatchback)

Lighting

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды