Chevrolet Sonic 2012 Скачать руководство пользователя страница 510 | Manualshive

Страница: 510 / 812

background image

Outside Rearview Mirror Glass Replacement

Removal Procedure

Warning: Approved safety glasses and gloves should be worn when performing this procedure to reduce the chance of

personal injury.

1. Place masking tape over the mirror glass.

2. Carefully push the outside rearview mirror glass upward and into the right corner of the mirror housing, allowing access to the

bottom edge.

3. Grasp the bottom edge of the mirror glass firmly, lift it up and pull rearward until the mirror glass releases the motor ring.

Installation Procedure

1. Place the mirror glass on the lower motor ring retainers.
2. Place one hand on the back of the mirror housing, using the flat palm of the other hand press inward locking the mirror glass

to the motor ring.

3. Remove the masking tape from the mirror glass.
4. Inspect the outside mirror for proper operation before installing the door trim panel.

© 2011 General Motors. All rights reserved.

Mirrors

BODY SYSTEMS

0-4

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
508
509
510
511
512
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: Valeo Страницы: 17

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

Бренд: Conrad Страницы: 26

2003 Thunderbird

Бренд: Ford Страницы: 200

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

Бренд: Axxess Страницы: 8

Бренд: SeaSucker Страницы: 9

Бренд: Lexus Страницы: 369

Бренд: Mountain Top Страницы: 12

Бренд: PAC Страницы: 4

STEALTH POWER RBP-216-SP

Бренд: RBP Страницы: 16

STREET SUPER SHIFTER

Бренд: HURST Страницы: 2

autoSteady AS101

Бренд: Enduro Страницы: 48

Бренд: Thule Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды