Chevrolet Sonic 2012 Скачать руководство пользователя страница 375 | Manualshive

Страница: 375 / 812

background image

Drivetrain and Front Suspension Frame Replacement

Special Tools

• EN-45059 Angle Meter
• CH-50619 Front Suspension Frame Adjusting Pins

For equivalent regional tools, refer to

Special Tools

.

Removal Procedure

1. Support the radiator and condenser from above using the upper brackets on each side.
2. Raise the vehicle on a hoist. Refer to

Lifting and Jacking the Vehicle

.

3. Remove the front tire and wheel assembly. Refer to

Tire and Wheel Removal and Installation

.

4. Remove the skid plate from the front frame, if equipped. Refer to

Drivetrain and Front Suspension Frame Skid Plate

Replacement

.

5. Remove the left and right front wheel house liner inner front extensions. Refer to

Front Wheelhouse Liner Inner Front

Extension Replacement

.

6. Remove the front bumper impact bar lower bracket. Refer to

Front Bumper Impact Bar Lower Bracket Replacement

.

7. Disconnect the steering linkage tie rod end from the steering knuckle. Refer to

Steering Linkage Outer Tie Rod Replacement .

8. Disconnect the lower ball joints from the steering knuckles. Refer to

Lower Control Arm Replacement .

9. Disconnect the stabilizer links from the strut assemblies.

10. Remove the steering rack retaining bolts

(1) and discard.

11. Using mechanics wire, secure the power steering gear to the vehicle.
12. Disconnect the hydraulic power steering hoses from the front frame, if equipped.
13. Disconnect the exhaust isolators

(2) from the front suspension frame.

14. Disconnect the power brake booster pump hose and connector, if equipped.
15. Remove the rear transmission mount bracket to rear mount through bolt

(1).

16. Using a suitable support table or equivalent, support the front suspension frame.

17. Remove the upper frame suspension retaining bolts

(1).

Frame and Underbody

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
373
374
375
376
377
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: Daihatsu Страницы: 43

Бренд: RACLET Страницы: 48

Бренд: RACLET Страницы: 31

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 20

Multiple G9F18 AU000

Бренд: Genesis Страницы: 3

Бренд: Roav Страницы: 10

Бренд: Metra Electronics Страницы: 2

Бренд: Alpine Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: Alpine Страницы: 8

Бренд: Toyota Страницы: 35

Бренд: Jeep Страницы: 380

Бренд: Sagem Страницы: 10

Бренд: Prorack Страницы: 15

Бренд: S&B Filters Страницы: 4

Бренд: Mazda Страницы: 3

Бренд: SIXTOL Страницы: 32

Бренд: Arctic Cat Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды