Chevrolet Sonic 2012 Скачать руководство пользователя страница 652

Страница: 652 / 812

(1) Center Front Impact Sensor—Located under

the hood at the center of the vehicle

(2) Passenger Instrument Panel Air Bag—Located

at the top right under the instrument panel

(3)

Right Roof Rail Air Bag—Located under the

headliner, extending from the passenger front
windshield pillar to the passenger rear

windshield pillar

(4)

Inflatable Restraint Sensing and Diagnostic

Module (SDM)—Located underneath the center
stack

(5)

Passenger Presence System (PPS)—Located on
the passenger front seat underneath the seat

bottom trim

(6)

Passenger Seat Belt Anchor Pretensioner—
Located on the outboard side of the
passengers seat

(7) Right Front Side Impact Sensor—Located at

the B-pillar underneath the door sill

(8) Inflator Module for Right Roof Rail Air Bag—

Located behind headliner at the upper B-pillar

(9) Passenger Seat Side Air Bag—Located on the

seat back of passenger seat

(10)

Passenger Seat Belt Retractor Pretensioner—

Located under the trim near the bottom of the
center pillar on the passenger side of vehicle

(11)

Driver Seat Belt Retractor Pretensioner—
Located under the trim near the bottom of the

center pillar on the driver side of vehicle

(12)

Driver Seat Side Air Bag—Located on the seat
back of driver seat

(13)

Inflator Module for Left Roof Rail Air Bag—
Located behind headliner at the upper B-pillar

(14)

Left Front Side Impact Sensor—Located at the
B-pillar underneath the door sill

(15) Driver Seat Belt Anchor Pretensioner—Located

on the outboard side of the drivers seat

(16)

Left Roof Rail Air Bag—Located under the
headliner, extending from the driver front

windshield pillar to the driver rear windshield
pillar

(17) Driver Steering Wheel Air Bag—Located on the

steering wheel

(18) Vehicle Battery—Located under the hood on

the left side

Component Locator

Restraints

RESTRAINTS

0-8

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды