Chevrolet Sonic 2012 Скачать руководство пользователя страница 771

Страница: 771 / 812

Heater Inlet Hose Replacement (1.2L or 1.4L)

Special Tools

BO-38185 Hose Clamp Pliers

For equivalent regional tools, Refer to

Special Tools

Removal Procedure

1. Drain the cooling system. Refer to

Cooling System Draining and Filling

2. Disconnect the heater inlet hose quick connect fitting

(1) at the heater core.

3. Remove the heater inlet hose

(2) from the heater core.

4. Remove the heater inlet hose clamp

(1) at the engine using BO-38185 Hose Clamp Pliers .

5. Remove the heater inlet hose

(2) from the engine.

6. Remove the heater inlet hose from the vehicle.

HEATING VENTILATION AND AIR CONDITIONING

Hvac

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды