Chevrolet Sonic 2012 Скачать руководство пользователя страница 804

Страница: 804 / 812

Installation Procedure

1. Install the radiator outlet hose to the vehicle.
2. Install the radiator outlet hose

(2) to the radiator.

3. Install the radiator outlet hose clamp

(1) at the radiator using BO-38185 Hose Clamp Pliers .

4. Install the radiator outlet hose

(2) to the engine.

5. Connect the radiator outlet hose quick connect fitting

(1) at the engine.

6. Lower the vehicle.
7. Fill the cooling system. Refer to

Cooling System Draining and Filling

BACK TO CHAPTER INDEX

SONIC

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды