Chevrolet Sonic 2012 Скачать руководство пользователя страница 774

Страница: 774 / 812

Installation Procedure

1. Install the heater inlet hose to the vehicle.
2. Install the heater inlet hose

(2) to the engine.

3. Install the heater inlet hose clamp

(1) at the engine using BO-38185 Hose Clamp Pliers .

4. Install the heater inlet hose

(2) from the heater core.

5. Connect the heater inlet hose quick connect fitting

(1) at the heater core.

6. Fill the cooling system. Refer to

Cooling System Draining and Filling

HEATING VENTILATION AND AIR CONDITIONING

Hvac

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды