Canon imageRUNNER ADVANCE C5255, Руководство по обслуживанию, Страница: 802 / 1443

7
7
7-111
7-111
Error•Jam•Alarm > Alarm Code > Alarm Code
Error•Jam•Alarm > Alarm Code > Alarm Code
Alarm Code
Alarm Code
Location
of Trouble
Alarm
Code
Description Details
00 - 0085 A notice of stat -
00 - 0246 Error code display
(4-digit)
Soft counter PCB cannot write normally.
00 - 0247 Error code display
(4-digit)
Soft counter PCB cannot restore data.
01 - 0001 Disabled to obtain
counter values for a
certain period of time
Counter information is not set to UGW
* Not displayed on service mode history due to the
alarm being generated by UGW
01 - 0004 Notification of IP address
change
IP address has been changed
* Not displayed on service mode history due to the
alarm being generated by UGW
01 - 0005 Machine is in restricted
operation mode
The machine has entered limited function mode due
to some reasons
* Not displayed on service mode history due to the
alarm being generated by UGW
02 - 0025 Insufficient Scanner
Unit (Paper Front) LED
light intensity alarm
(Some of the LEDs are
OFF. Scanning can be
continued.)
In the case that the light intensity is insufficient at
LED lighting.
04 - 0008 Optional deck lifter error -
04 - 0010 Jam left untouched Jam is left untouched
* Not displayed on service mode history due to the
alarm being generated by UGW
10 - 0001 Toner low (Black) Toner (Bk) level warning display
* Not displayed on service mode history due to the
alarm being generated by UGW
10 - 0002 Toner low (Cyan) Toner (C) level warning display
* Not displayed on service mode history due to the
alarm being generated by UGW
10 - 0003 Toner low (Magenta) Toner (M) level warning display
* Not displayed on service mode history due to the
alarm being generated by UGW
10 - 0004 Toner low (Yellow) Toner (Y) level warning display
* Not displayed on service mode history due to the
alarm being generated by UGW
10 - 0017 Toner (Y) prior delivery
alarm
-
Location
of Trouble
Alarm
Code
Description Details
10 - 0018 Toner (M) prior delivery
alarm
-
10 - 0019 Toner (C) prior delivery
alarm
-
10 - 0020 Toner (Bk) prior delivery
alarm
-
10 - 0022 Patch detection light
intensity abnormal
change alarm
-
10 - 0100 Toner bottle change
notification alarm
-
11 - 0001 Waste toner alarm Detected waste toner bottle full.
11 - 0010 Near-full state of the
Waste Toner Container
Detection of near-full state of the Waste Toner
Container
30 - 0002 Charge loss of
secondary transfer roller
Charge loss of secondary transfer roller was
detected.
31 - 0006 HDD failure when the
mirroring function is
installed
Movement: HDD failure when the mirroring function
is installed
Cause: The HDD has a failure when the mirroring
function is installed
Measures: Check the connection among the
following: the HDD that corresponds to the red LED
on the LED PCB of the Mirroring Kit, the Mirroring
Board and the Main Controller PCB 2.
Replace the HDD if it cannot be recovered.
31 - 0008 HDD failure prediction
alarm
Movement: HDD failure is expected to occur in a
short time due to occurrence of physical error in
HDD. It does not occur in the HDD of mirroring
configuration.
Cause: Error in the S.M.A.R.T. value of HDD
Measures:
1. Back up the data stored in HDD.
2. Replace the HDD.
3. Restore the data.
S.M.A.R.T. (Self-Monitoring Analysis and Reporting
Technology): Self-diagnosis function built in the HDD.
The occurrence rate of reading error, reading and
writing speed, the total number of Motor start-up and
stop times, the total length of power-on time, etc. are
monitored.
33 - 0010 Scanner Unit Exhaust
Fan (FM1) alarm
The fan rotation signal cannot be detected after
3 seconds have passed since the Scanner Unit
Exhaust Fan (FM1) of the Reader is turned ON.
Check the connector connection -> Replace the
Scanner Unit Exhaust Fan (FM1).