Canon imageRUNNER ADVANCE C5255, Руководство по обслуживанию, Страница: 718 / 1443

7
7
7-27
7-27
Error•Jam•Alarm > Error Code > Error Code Details
Error•Jam•Alarm > Error Code > Error Code Details
E
code
Detailed
code
Occurance
area
Items Description
E027 0300 05 Title Error in supply with C Developing Assembly
Description Failure in detection about the changes of ON => OFF =>
ON with the sensor which detects a full rotation of the
supply screw within the specified period of time.
Remedy 1. Check the damage of the Developing Coupling.
If it’s damaged, replace the Developing Assembly.
2. Check the damage of the coupling (with the Developing
Assembly) at the Host Machine side.
If it’s damaged, remove the Main Drive Unit to replace the
coupling.
3. Turn the motor as a single unit while the Drum/
Developing Assembly is removed to check rotation of the
Main Drive Unit.
If it does not rotate, replace the Motor.
If the above measures do not solve the problem, replace
the Drum Driver PCB (UN4).
If there still remains the problem, replace the Main Drive
Unit.
4. Remove the Hopper Unit and manually turn the Supply
Input Gear to check rotation.
If it’s results in NG, replace the Hopper Unit.
E027 0400 05 Title Error in supply with Bk Developing Assembly
Description Failure in detection about the changes of ON => OFF =>
ON with the sensor which detects a full rotation of the
supply screw within the specified period of time.
Remedy 1. Check the damage of the Developing Coupling.
If it’s damaged, replace the Developing Assembly.
2. Check the damage of the coupling (with the Developing
Assembly) at the Host Machine side.
If it’s damaged, remove the Main Drive Unit to replace the
coupling.
3. Turn the motor as a single unit while the Drum/
Developing Assembly is removed to check rotation of the
Main Drive Unit.
If it does not rotate, replace the Motor.
If the above measures do not solve the problem, replace
the Drum Driver PCB (UN4).
If there still remains the problem, replace the Main Drive
Unit.
4. Remove the Hopper Unit and manually turn the Supply
Input Gear to check rotation.
If it’s results in NG, replace the Hopper Unit.
E
code
Detailed
code
Occurance
area
Items Description
E029 0003 05 Title ITB light intensity error
Description The reflected value from ITB was lower than the lower
limit when adjusting the light intensity of patch LED.
Remedy 1. Check if the cable of the Registration Shutter Solenoid
(SL1) is open circuit.
2. Check if the cable of the Patch Sensor (Front, Rear)
(UN47, 48) is open circuit.
3. Check the installation of the ITB Unit.
4. Replace the Patch Sensor Unit.
5. Replace the Registration Shutter Solenoid (SL1).
E045 0000 05 Title Error in Transparency Sensor
Description When the power is ON or the door is closed, the light
failed to be back although there is no paper.
Remedy 1. Check installation or soil of the Transparency Sensor
(UN51) and the prism.
2. Check the Sensor Harness (to see if the harness is
caught, disconnected or physically removed).
3. Replace the Transparency Sensor.
4. Replace the Pickup Feed Driver PCB (UN2).
E061 0001 05 Title Abnormal current run to the Y Drum
Description Abnormal current run to the Y Drum (small current level
or no drum is found)
Remedy 1. Check installation of the Drum Unit.
2. Check if there is failure in grounding contact at the
Drum Unit side (such as loosened screw which secures
the plate at the contact point).
3. Check if there is failure in grounding contact with the
Drum at Process Unit side.
4. Replace the Drum Unit.
5. Replace the Pre-exposure LED PCB (UN23,UN24).
E061 00E0 05 Title Abnormal current run to the Y Drum
Description The change in current level for Y Drum film thickness
detection is too much compared to the previous time.
Remedy 1. Check with the Host Machine which generates an error
to check if a wrong cartridge (which is different from the
initialized cartridge) is installed.
2. Check if there is failure in grounding contact at the
Drum Unit side (such as loosened screw which secures
the plate at the contact point)
3. Check if there is failure in grounding contact with the
Drum at Process Unit side.
4. Replace the Drum Unit.
5. Replace the Pre-exposure LED PCB (UN23,UN24).