manualshive.com logo in svg

Atmel ATSAML22G16A-AUT, Руководство пользователя

Atmel ATSAML22G16A-AUT - это микроконтроллер с широкими возможностями и высокой производительностью. Загрузите его бесплатное руководство по эксплуатации с нашего сайта для получения подробной информации о его функциональности. Получите доступ к руководству по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

The request is cleared when any SDATAL/Hx register is written to. Refer to 

Frame Counters

 for

details.
The frame counter associated to the DMA request is the same as the interrupt source, refer also to 

Interrupts

.

•

Automated Character Mapping Data Ready (ACMDRDY): the request is set when the frame
counter associated to automated character mapping function overflows. The request is cleared
when CMDATA register is written. Refer to 

Automated Character Mapping

 for details.

•

Automated Bit Mapping Data Ready (ABMDRDY): the request is set when the frame counter
associated to automated bit mapping function overflows. The request is cleared when ISDATA
register is written. Refer to 

Automated Bit Mapping

 for details.

Note: 

 If the CPU accesses the registers which are source of DMA request set/clear condition, the DMA

request can be lost or the DMA transfer can be corrupted, if enabled.

43.6.4.  Interrupts

The SLCD has the following interrupt sources:

•

Frame Counter 0 Overflows (FC0O): Indicates that the frame counter 0 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

•

Frame Counter 1 Overflows (FC1O): Indicates that the frame counter 1 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

•

Frame Counter 2 Overflows (FC2O): Indicates that the frame counter 2 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

•

VLCD Ready Toggle (VLCDRT): Indicates that status of LCD Ready has changed.

•

VLCD Status Toggle (VLCDST): Indicates that relation between VLCD and chip VDD has changed.

•

Pump Run Status Toggle (PRST): Indicates that Pump Run Status has changed.

Each interrupt source has an interrupt flag associated with it. The interrupt flag in the Interrupt Flag Status
and Clear (INTFLAG) register is set when the interrupt condition occurs. Each interrupt can be individually
enabled by writing a one to the corresponding bit in the Interrupt Enable Set (INTENSET) register, and
disabled by writing a one to the corresponding bit in the Interrupt Enable Clear (INTENCLR) register. An
interrupt request is generated when the interrupt flag is set and the corresponding interrupt is enabled.
The interrupt request remains active until the interrupt flag is cleared, the interrupt is disabled, or the
SLCD is reset. See 

INTFLAG

 for details on how to clear interrupt flags. All interrupt requests from the

peripheral are ORed together on system level to generate one combined interrupt request to the NVIC.
Refer to the Nested Vector Interrupt Controller for details. The user must read the INTFLAG register to
determine which interrupt condition is present.

Note: 

 Interrupts must be globally enabled for interrupt requests to be generated.

43.6.5.  Events

The SLCD can generate the following output events:

•

Frame Counter 0 Overflow (FC0O): Indicates that the frame counter 0 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

•

Frame Counter 1 Overflow (FC1O): Indicates that the frame counter 1 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

•

Frame Counter 0 Overflow (FC2O): Indicates that the frame counter 2 has overflowed, it has
reached its top value and wrapped to zero. Refer to 

Frame Counters

 for details.

Writing a '1' to an Event Output bit in the Event Control Register enables the corresponding output event.
Writing a '0' to this bit disables the corresponding output event.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

1086

Содержание ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATSAML22G16A-AUT

G1SLE MK2 Alignment Manual preview
MK2
Бренд: G1SLE Страницы: 2
ZKTeco PA10 Quick Start Manual preview
PA10
Бренд: ZKTeco Страницы: 8
EasyIO FT Series User Reference preview
FT Series
Бренд: EasyIO Страницы: 18
L. G. B. 51099 Instructions preview
51099
Бренд: L. G. B. Страницы: 2
L-Acoustics LA4X Product Information preview
LA4X
Бренд: L-Acoustics Страницы: 36
Sutter Instrument TRIO MPC-165 Series Operation Manual preview
TRIO MPC-165 Series
Бренд: Sutter Instrument Страницы: 60
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Бренд: YASKAWA Страницы: 12
KBR multicomp F144-MS-1V1C1TI6RO-3 User Manual preview
multicomp F144-MS-1V1C1TI6RO-3
Бренд: KBR Страницы: 68
Kramer FC-21ETH User Manual preview
FC-21ETH
Бренд: Kramer Страницы: 60
Zeversolar Zeverlution S Setup Manual preview
Zeverlution S
Бренд: Zeversolar Страницы: 8
ECUE DMX2CC 12ch Setup Manual preview
DMX2CC 12ch
Бренд: ECUE Страницы: 39
Regada SP 1 Installation, Service And Maintenance Instructions preview
SP 1
Бренд: Regada Страницы: 41
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Бренд: KEPCO Страницы: 34
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Бренд: mikroElektronika Страницы: 35
Danfoss MCX08M User Manual preview
MCX08M
Бренд: Danfoss Страницы: 72
BZ PRODUCTS BZ 7/12 Installation Manual preview
BZ 7/12
Бренд: BZ PRODUCTS Страницы: 3
Spruce PS-SPRWIFI16-01 Setup Manual preview
PS-SPRWIFI16-01
Бренд: Spruce Страницы: 8
XICOY LGC 13C User Manual preview
LGC 13C
Бренд: XICOY Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды