Atmel ATSAML22G16A-AUT Скачать руководство пользователя страница 797 | Manualshive

Страница: 797 / 1231

background image

36.5. Product Dependencies

In order to use this peripheral, other parts of the system must be configured correctly, as described below.

36.5.1. I/O Lines

In order to use the I/O lines of this peripheral, the I/O pins must be configured using the I/O Pin Controller
(PORT).

Related Links

PORT: IO Pin Controller

on page 538

36.5.2. Power Management

This peripheral can continue to operate in any sleep mode where its source clock is running. The
interrupts can wake up the device from sleep modes. Events connected to the event system can trigger
other operations in the system without exiting sleep modes.

36.5.3. Clocks

The TCC bus clock (CLK_TCCx_APB, with x instance number of the TCCx) is enabled by default, and
can be enabled and disabled in the Main Clock.

A generic clock (GCLK_TCCx) is required to clock the TCC. This clock must be configured and enabled
in the generic clock controller before using the TCC.

The generic clocks (GCLK_TCCx) are asynchronous to the bus clock (CLK_TCCx_APB). Due to this
asynchronicity, writing certain registers will require synchronization between the clock domains. Refer to

Synchronization

for further details.

Related Links

Peripheral Clock Masking

on page 145

GCLK - Generic Clock Controller

on page 121

36.5.4. DMA

The DMA request lines are connected to the DMA Controller (DMAC). In order to use DMA requests with
this peripheral the DMAC must be configured first. Refer to

DMAC – Direct Memory Access Controller

for

details.

Related Links

DMAC – Direct Memory Access Controller

on page 432

36.5.5. Interrupts

The interrupt request line is connected to the Interrupt Controller. In order to use interrupt requests of this
peripheral, the Interrupt Controller (NVIC) must be configured first. Refer to

Nested Vector Interrupt

Controller

for details.

Related Links

Nested Vector Interrupt Controller

36.5.6. Events

The events of this peripheral are connected to the Event System.

Related Links

EVSYS – Event System

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

797

«
...
795
796
797
798
799
...
»

Содержание ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATSAML22G16A-AUT

Бренд: Particle Страницы: 6

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 64

Бренд: ZKTeco Страницы: 14

Бренд: Unico Страницы: 164

Бренд: National Instruments Страницы: 78

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

Бренд: Greenheck Страницы: 4

Бренд: VMK Страницы: 98

Бренд: TSM Страницы: 2

Бренд: Gateway Страницы: 2

Бренд: Oriental motor Страницы: 4

Бренд: Rare Waves Страницы: 18

Бренд: Curtis Страницы: 30

Бренд: Hoffer Страницы: 57

AquaLink RS All Button

Бренд: Jandy Страницы: 2

BoxControl Compact

Бренд: elero Страницы: 8

Бренд: TAC Vista Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды