Atmel ATSAML22G16A-AUT Скачать руководство пользователя страница 656 | Manualshive

Страница: 656 / 1231

background image

enabled by writing '1' to the corresponding bit in the Interrupt Enable Set register (INTENSET), and
disabled by writing '1' to the corresponding bit in the Interrupt Enable Clear register (INTENCLR).

An interrupt request is generated when the interrupt flag is set and if the corresponding interrupt is
enabled. The interrupt request remains active until either the interrupt flag is cleared, the interrupt is
disabled, or the SPI is reset. For details on clearing interrupt flags, refer to the INTFLAG register
description.

The SPI has one common interrupt request line for all the interrupt sources. The value of INTFLAG
indicates which interrupt is executed. Note that interrupts must be globally enabled for interrupt requests.
Refer to

Nested Vector Interrupt Controller

for details.

Related Links

Nested Vector Interrupt Controller

33.6.4.3. Events

Not applicable.

33.6.5. Sleep Mode Operation

The behavior in sleep mode is depending on the master/slave configuration and the Run In Standby bit in
the Control A register (CTRLA.RUNSTDBY):

•

Master operation, CTRLA.RUNSTDBY=1: The peripheral clock GCLK_SERCOM_CORE will
continue to run in idle sleep mode and in standby sleep mode. Any interrupt can wake up the
device.

•

Master operation, CTRLA.RUNSTDBY=0: GLK_SERCOMx_CORE will be disabled after the
ongoing transaction is finished. Any interrupt can wake up the device.

•

Slave operation, CTRLA.RUNSTDBY=1: The Receive Complete interrupt can wake up the device.

•

Slave operation, CTRLA.RUNSTDBY=0: All reception will be dropped, including the ongoing
transaction.

33.6.6. Synchronization

Due to asynchronicity between the main clock domain and the peripheral clock domains, some registers
need to be synchronized when written or read.

The following bits are synchronized when written:

•

Software Reset bit in the CTRLA register (CTRLA.SWRST)

•

Enable bit in the CTRLA register (CTRLA.ENABLE)

•

Receiver Enable bit in the CTRLB register (CTRLB.RXEN)

Note:

CTRLB.RXEN is write-synchronized somewhat differently. See also

for details.

Required write-synchronization is denoted by the "Write-Synchronized" property in the register
description.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

656

«
...
654
655
656
657
658
...
»

Содержание ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATSAML22G16A-AUT

Бренд: Vacon Страницы: 62

Бренд: Parker Страницы: 44

Бренд: Samson Страницы: 6

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Newport Страницы: 417

Бренд: Full Gauge Controls Страницы: 3

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 340

Бренд: ETC Страницы: 8

Бренд: Texas Instruments Страницы: 27

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Parker Страницы: 24

BMS NUV100-CI-12

Бренд: Nuvation Страницы: 41

Бренд: National Instruments Страницы: 100

Бренд: CASTLE Страницы: 2

MultiBloc MBC-1200-SE S22

Бренд: Dungs Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды