Atmel ATSAML22G16A-AUT Скачать руководство пользователя страница 594 | Manualshive

Страница: 594 / 1231

background image

Related Links

PM – Power Manager

31.5.3. Clocks

The SERCOM bus clock (CLK_SERCOMx_APB) is enabled by default, and can be enabled and disabled
in the Main Clock.

The SERCOM uses two generic clocks: GCLK_SERCOMx_CORE and GCLK_SERCOMx_SLOW. The
core clock (GCLK_SERCOMx_CORE) is required to clock the SERCOM while working as a master. The
slow clock (GCLK_SERCOMx_SLOW) is only required for certain functions. See specific mode chapters
for details.

These clocks must be configured and enabled in the Generic Clock Controller (GCLK) before using the
SERCOM.

The generic clocks are asynchronous to the user interface clock (CLK_SERCOMx_APB). Due to this
asynchronicity, writing to certain registers will require synchronization between the clock domains. Refer
to

Synchronization

Related Links

GCLK - Generic Clock Controller

on page 121

MCLK – Main Clock

on page 141

31.5.4. DMA

The DMA request lines are connected to the DMA Controller (DMAC). The DMAC must be configured
before the SERCOM DMA requests are used.

Related Links

DMAC – Direct Memory Access Controller

on page 432

31.5.5. Interrupts

The interrupt request line is connected to the Interrupt Controller (NVIC). The NVIC must be configured
before the SERCOM interrupts are used.

Related Links

Nested Vector Interrupt Controller

31.5.6. Events

Not applicable.

31.5.7. Debug Operation

When the CPU is halted in debug mode, this peripheral will continue normal operation. If the peripheral is
configured to require periodical service by the CPU through interrupts or similar, improper operation or
data loss may result during debugging. This peripheral can be forced to halt operation during debugging -
refer to the Debug Control (DBGCTRL) register for details.

31.5.8. Register Access Protection

All registers with write-access can be write-protected optionally by the Peripheral Access Controller
(PAC), except the following registers:

•

Interrupt Flag Clear and Status register (INTFLAG)

•

Status register (STATUS)

•

Data register (DATA)

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

594

«
...
592
593
594
595
596
...
»

Содержание ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATSAML22G16A-AUT

Бренд: S&C Страницы: 34

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

Бренд: Gardena Страницы: 17

Бренд: Badger Meter Страницы: 16

Бренд: IFM Страницы: 49

Бренд: Matelec Страницы: 16

Бренд: Gardena Страницы: 236

Бренд: Industrial Controls Страницы: 17

Бренд: BQT Страницы: 2

Бренд: A & H Страницы: 35

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: YASKAWA Страницы: 42

Бренд: YASKAWA Страницы: 351

Бренд: Gardena Страницы: 15

Бренд: Lumel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды