background image

 

 

Setup Guide

 

support.spruceirrigation.com

 

 

 

FCC Compliance Statement

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may 
not cause harmful interference, and (2) this device must accept any interference received, including interference that may

 

cause undesired operation.

 

 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 
that interference will not occur in a particular installation. If this equipment does cause harmful interference to

 

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

 

-

 Reorient or relocate the receiving antenna.

 

-

 Increase the separation between the equipment and receiver.

 

-

 Connect the equipment to an outlet on a circuit different from that to which the

 

receiver is connected.

 

-

 Consult an experienced radio/TV technician for help.

 

Changes or modifications to this product not authorized by Plaid Systems could void the electromagnetic compatibility and 
wireless compliance and negate your authority to operate the product.

 

 

Canada Statement

 

This Class B digital apparatus complies with Canadian ICES

-

003. This device complies with Industry Canada license

-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, 
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

 

www.spruceirrigation.com/terms

 

© 2018 Plaid Systems

 

Spruce and the Spruce Logo are trademarks of 
Plaid Systems. App guidance is for instructional 
purposes only and may differ from actual 
product. Subject to change without notice.

 

Spruce

™ 

WiFi Smart Irrigation Controller 16

 

Model Number: PS

-

SPRWIFI16

-

01

 

Contains FCC IDs:

 

XFF

-

Z357PA20

 

COFWMNVM11

 

Содержание PS-SPRWIFI16-01









Отзывы: