11
followed by the <#> button to kiss-off the domestic alarm reports.
If you make a mistake when entering the kiss-off code, pressing the <#> button will clear all previous digits received at
the panel and you can now enter in the correct code.
INSTALLING PROXIMITY READER
There are three proximity readers that can be connected to the control panel. They are;
1-Arm Reader
(Indoor Only)
2-Proximity only Access Reader
Indoor / Outdoor)
3-Proximity and keypad (PIN) Access Reader
Indoor / Outdoor
The ARM Reader is generally to be used for selective arming or disarming of either Area “A” or “B” or both. By presenting
a valid access tag or card to the reader the user can then arm or disarm the panel using the “A” & “B” buttons on the
reader. On presenting a valid tag to the reader, the current status of Areas A & B will be shown on the two LED’s. The
user has 4 seconds to make a new selection before the reader will timeout and the tag will have to be re-presented
again. The Areas allowed to be controlled by the user must be programmed by the installer. If the User is allowed to
fully Arm or arm Stay Mode then they can cycle through the various states (eg Disarmed, Full Armed, Stay Armed). As
the “A” or “B” button is pressed the associated LED will change to indicate the new state, eg if the Disarmed state was
selected the LED will be GREEN, If the Armed state was selected the LED will be RED and if Stay Mode was selected the
LED would be flashing RED. Four seconds after the last button was pressed the reader will action the new armed status
and the LED’s will turn off. If the reader has also been programmed to allow the “1& 3 PANIC” function at that keypad
number a “PANIC” alarm will be generated if the “A” & “B” buttons are pressed simultaneously (see P72E option 5).
NOTE:
From the disarmed state you can select Armed or Stay modes but if already Armed or in Stay Mode you MUST
disarm first (letting the reader timeout) before you can select a new armed state.
The second reader is generally going to be used as an access control reader although if the tag is allowed to Arm/Disarm
the alarm then this will also happen when the tag is presented. For access control, if a tag or card is presented to the
reader the associated door lock will release via an output on the control panel. There is also an output at the reader
which can be used to unlock the door if desired (see drawing on following page for details). The output number at the
reader follows the keypad address number, eg if the reader has been assigned to keypad address 5, the output at the
reader will follow all programming associated with output 5.
The third reader is generally going to be used as an access control reader as well although if the tag is allowed to Arm/
Disarm the alarm then this will also happen when the tag is presented. This reader combines a proximity reader with a
full keypad. Depending on program options the reader can be set-up to operate on a proximity tag or card only, on en-
tering of a valid user code only, or on presentation of the tag/card followed by the user code (PIN). If the presented tag
requires a PIN number to be entered, the LED on the reader will flash for 5 seconds after a valid tag to indicate that the
PIN number should now be entered. There is also an output available on this reader that follows the same addressing
functionality as described above.
If the two button “PANIC”, “FIRE” or “MEDICAL” functions are programmed to the keypad (see P72E Options 5,6 & 7)
these manual alarms can be generated at the reader by pressing “1” & “2” for “PANIC”, “3” & “4” for “FIRE” and “5” & “6”
for “MEDICAL” alarms.
On each of the three readers there is an optional input (see drawings on following page). This input is not EOL moni-
tored so it should only be used for non-critical monitoring functions, eg monitoring an exterior gate to show if it is cur-
rently opened or closed. A zone can be programmed to use this input for its trigger (see P122E Option 4) so that the
state of the input can be displayed on a keypad. The inputs are linked to the selected keypad address programmed into
the reader. For example if the reader being used was programmed as keypad # 1, then the input can be assigned to
zone 1 or 9 (at location P122E), if the keypad address was # 8, the input can then be assigned to zone 8 or 16. Also, the
LED on reader types 2 & 3 can be linked to an output so that special functions may be displayed at the reader if desired
(see P98E). Each reader must have a unique keypad address number from 1-8 assigned so that the various program op-
tions can be assigned. This is explained in detail on Page 65.
NOTE:
The proximity readers flash out the assigned keypad address number on the LED whenever the panel is in
“Installer Program” Mode. This allows quick identification of the assigned address for each reader.
