20
To ch
ange the keypad address so that it is different to others connected to the panel,
Press
<PROG> <902> <ENTER>
. The Keypad display will show
“KP:1”
. To change the keypad address so that it is differ-
ent to others connected to the panel, press a number on the keypad from 1-8 relating to the address you wish to assign
to the keypad, e.g. if the keypad is the second one connected to the panel and the other keypad is set to address 1, press
2 to select keypad address 2 for this keypad. The selected address will be displayed on the Icon LCD (in this example
KP:2
).
Press
<ENTER>
to save the change.
ICON LCD KEYPAD ADJUSTMENTS
Local Program Mode also gives you the ability to adjust some individual Keypad functionality.
Once in Program Mode using the
<PROG>
<BYPASS>
&
<ENTER>
and the display showing
“LPGM”
use the program-
ming addresses below to make changes if required;
<PROG> <900> <ENTER>
1 ON
= 12-hour Clock,
1 OFF
= 24-hour Clock
2 ON
= Clock & Temperature Displayed alternatively,
2 OFF
= Clock only
3 ON
= Display Temperature with ENTER button is pressed,
3 OFF
= Feature Disabled
4 ON
= NOT USED
5 ON
= All Lights will turn off after 90 seconds of inactivity
<PROG> <901> <ENTER>
Keypad Software Version display
<PROG> <902> <ENTER>
Keypad Address
(1-8) All Keypads on the same system must have a different address
<PROG> <903> <ENTER>
Calibrate Temperature Sensor
the current temp will be displayed
(Warning, don’t adjust this location unless you have a calibrated temp source available)
<PROG> <904> <ENTER>
Backlight Brightness
display will show
“B/L”
to adjust press
<MEMORY
↑
>
to
increase
or
<STAY
↓
>
to decrease.
<PROG> <905> <ENTER>
LCD Contrast
display will show
“CTRS”
to adjust press
<MEMORY
↑
>
to increase
or
<STAY
↓
>
to decrease.
<PROG> <906> <ENTER>
Buzzer Tone
display will show
“BUZ”
to adjust press
<MEMORY
↑
>
to increase
or
<STAY
↓
>
to decrease.
<PROG> <920> <ENTER>
Default
all Keypad Local Programming Options will be returned to factory default
Note:
after adjusting any programming options,
<ENTER>
must be pressed to save changes.
*You can not access Local Programming Mode if the system is Armed or Stay Armed.
LCD KEYPAD ADDRESS ASSIGNMENT
Setting the LCD keypad address is done in
“Local Program Mode”
.
To enter
“Local Program Mode”
on the LCD Keypad, press AND HOLD the
<CONTROL>
button down and within 3 sec-
onds press and hold the
<ARM>
button until the displays shows
“Local Mode”
.
When in Local Program Mode, the display will show
“local mode kb 1”
with the number 1 meaning the keypad address is
currently 1.
To change the keypad address press
<PROGRAM> <996> <ENTER>
.
The Keypad display will show
“Keypad Number 1”
then press a number on the keypad from 1-8 relating to the address
you wish to assign to the keypad, e.g. if the keypad is the second one connected to the panel and the other keypad is set
to address 1, press 2 to select keypad address 2 for this keypad. Then press
<ENTER>
to save.
To exit Local Program Mode, press and hold the
<PROGRAM>
button for 2 seconds.
During Local Program Mode, you can select the program option location directly or there is also a menu to navigate
through the various options.
