Toshiba TMPR7901 User Manual Download Page 129 | Manualshive

Page: 129 / 309

background image

Chapter 8: PCI/G-Bus Bridge

TX7901 User’s Manual (Rev. 6.30T – Nov, 2001)

8-7

8.2.2.2 “Retry”

Phase

The PGB records the address of the current cycle along with the word count and goes into a
delayed read state. The Bridge ignores new read or write transactions from the G-Bus side
by issuing Retries. When the read is finished on the PCI side, the PGB waits for the G-Bus
Master to re-issue the Delayed Read transaction on the G-Bus (Address and word count
compare) and completes the transaction at that time. An “Orphaned Read” results if the G-
Bus Master that initiated the Delayed Read does not return to complete the read. The PGB
reports orphaned reads by posting an interrupt after a timeout period equal to 2

16

clocks.

The PGB causes a G-Bus timeout on all PCI errors (parity or fatal) that happen during this
phase. To do this, the PGB issues a retry to all cycles with any address not equal to the
failed address, and then causes a timeout for the next request to the failed address.

The PGB will flush any posted writes from the G-Bus to PCI before performing any read
from a PCI slave. This is performed by first posting a retry to G-Bus Master read requests
and then completing the posted write.

«
...
127
128
129
130
131
...
»

Summary of Contents for TMPR7901






















































































































































































































































































































Reviews:

No comments

Related manuals for TMPR7901

Brand: ABB Pages: 63

Brand: Hable Pages: 3

Brand: Yamaha Pages: 92

E4KP ENTRYCHECK

Brand: SDC Pages: 6

Brand: SKF Pages: 11

Brand: Danfoss Pages: 162

Brand: H3C Pages: 16

Brand: HANYOUNG NUX Pages: 4

Brand: Srne Pages: 13

NetGuardian LPG D-PK-NGLPG

Brand: DPS Telecom Pages: 82

Brand: NELSEN WATER Pages: 16

Brand: Instruments of Things Pages: 12

Brand: GreenFlux Pages: 35

Brand: Unitech Pages: 15

Smatrix Wave PLUS

Brand: Uponor Pages: 4

Brand: Balmar Pages: 24

Brand: Comunello Pages: 112

Brand: Grundfos Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands