Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 698 | Manualshive

Page: 698 / 1141

background image

MSUBF32 MRd, MRe, MRf ||MMOV32 MRa, mem32

32-Bit Floating-Point Subtraction with Parallel Move

Operands

MRd

CLA floating-point destination register (MR0 to MR3) for the
MSUBF32 operation
MRd cannot be the same register as MRa

MRe

CLA floating-point source register (MR0 to MR3) for the MSUBF32
operation

MRf

CLA floating-point source register (MR0 to MR3) for the MSUBF32
operation

MRa

CLA floating-point destination register (MR0 to MR3) for the
MMOV32 operation
MRa cannot be the same register as MRd

mem32

32-bit memory location accessed using one of the available
addressing modes. Source for the MMOV32 operation.

Opcode

LSW: mmmm mmmm mmmm mmmm

MSW: 0010 ffee ddaa addr

Description

Subtract the contents of two floating-point registers and move from memory to a floating-
point register.

MRd = MRe - MRf;

MRa = [mem32];

Restrictions

The destination register for the MSUBF32 and the MMOV32 must be unique. That is,
MRa cannot be the same register as MRd.

Flags

This instruction modifies the following flags in the MSTF register:

Flag

TF

ZF

NF

LUF

LVF

Modified

No

Yes

Yes

Yes

Yes

The MSTF register flags are modified as follows:
• LUF = 1 if MSUBF32 generates an underflow condition.
• LVF = 1 if MSUBF32 generates an overflow condition.

The MMOV32 Instruction will set the NF and ZF flags.

Pipeline

Both MSUBF32 and MMOV32 complete in a single cycle.

Example

NF = MRa(31);

ZF = 0;

if(MRa(30:23) == 0) { ZF = 1; NF = 0; }

See also

MSUBF32 MRa, MRb, MRc
MSUBF32 MRa, #16FHi, MRb
MMPYF32 MRa, MRb, MRc || MSUBF32 MRd, MRe, MRf

Control Law Accelerator (CLA)

698

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

«
...
696
697
698
699
700
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: Facility Explorer Pages: 4

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: IDTECK Pages: 94

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: Lab.gruppen Pages: 2

Brand: Watlow Pages: 20

Network Device NXC-8160s

Brand: ZyXEL Communications Pages: 67

PCI-to-IDE ATA-133

Brand: Acard Pages: 33

Brand: Leader Pages: 46

Brand: Ekinex Pages: 4

Brand: Hanna Instruments Pages: 44

Brand: Yardian Pages: 52

Brand: Aube Technologies Pages: 12

Kaysun KC-03.2 SPS

Brand: Frigicoll Pages: 44

Thermal Entry Wizard

Brand: ATN Pages: 56

Brand: Galletti Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands