manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Technical Reference Manual

Share
Download
Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 96

1.3.4 CPU Watchdog Block

The watchdog module generates an output pulse, 512 oscillator-clocks (OSCCLK) wide whenever the 8-bit 
watchdog up counter has reached its maximum value. To prevent this, the user can either disable the counter 
or the software must periodically write a 0x55 + 0xAA sequence into the watchdog key register which resets the 
watchdog counter. 

Figure 1-44

 shows the various functional blocks within the watchdog module.

A.

The WDRST and XRS signals are driven low for 512 OSCCLK cycles when a watchdog reset occurs. Likewise, if the watchdog interrupt 
is enabled, the WDINT signal will be driven low for 512 OSCCLK cycles when an interrupt occurs.

Figure 1-44. CPU Watchdog Module

System Control and Interrupts

www.ti.com

96

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands