Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 988 | Manualshive

Page: 988 / 1141

background image

Table 15-91. PCR Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

7

SCLKME

R/W

0h

Sample rate generator input clock mode bit. The sample rate
generator can produce a clock signal, CLKG. The frequency of
CLKG is:
CLKG freq. = (Input clock frequency) / ( 1)
SCLKME is used in conjunction with the CLKSM bit to select the
input clock.
SCLKME CLKSM Input Clock For
Sample Rate Generator
0 0 Reserved
0 1 LSPCLK
The input clock for the sample rate generator is taken from the
MCLKR pin or from the MCLKX pin, depending on the value of the
CLKSM bit of SRGR2:
SCLKME CLKSM Input Clock For
Sample Rate Generator
1 0 Signal on MCLKR pin
1 1 Signal on MCLKX pin
Reset type: SYSRSn

6-4

RESERVED

R

0h

Reserved

3

FSXP

R/W

0h

Transmit frame-synchronization polarity bit. FSXP determines the
polarity of FSX as seen on the FSX pin.
Reset type: SYSRSn
0h (R/W) = Transmit frame-synchronization pulses are active high.
1h (R/W) = Transmit frame-synchronization pulses are active low.

2

FSRP

R

0h

Receive frame-synchronization polarity bit. FSRP determines the
polarity of FSR as seen on the FSR pin.
Reset type: SYSRSn
0h (R/W) = Receive frame-synchronization pulses are active high.
1h (R/W) = Receive frame-synchronization pulses are active low.

1

CLKXP

R

0h

Transmit clock polarity bit. CLKXP determines the polarity of CLKX
as seen on the MCLKX pin.
Reset type: SYSRSn
0h (R/W) = Transmit data is sampled on the rising edge of CLKX.
1h (R/W) = Transmit data is sampled on the falling edge of CLKX.

0

CLKRP

R/W

0h

Receive clock polarity bit. CLKRP determines the polarity of CLKR
as seen on the MCLKR pin.
Reset type: SYSRSn
0h (R/W) = Receive data is sampled on the falling edge of MCLKR.
1h (R/W) = Receive data is sampled on the rising edge of MCLKR.

Multichannel Buffered Serial Port (McBSP)

988

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

«
...
986
987
988
989
990
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: Aalborg Pages: 128

Minas A4 Series

Brand: Panasonic Pages: 5

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: RBH Access Technologies Pages: 36

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brand: SYCLOPE electronic Pages: 40

Pearldex Series

Brand: KaMo Pages: 2

Brand: CORNING Pages: 142

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Brand: FuzzDog Pages: 9

DMC-40x0 Series

Brand: Galil Motion Control Pages: 280

Brand: Electrosmith Pages: 32

Brand: BCH Electric Pages: 452

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands