Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 92 | Manualshive

Page: 92 / 1141

background image

1.3.2.7.1.6 NMI Watchdog Period (NMIWDPRD) Register

Figure 1-41. NMI Watchdog Period (NMIWDPRD) Register

15

0

NMIWDPRD

R/W-0xFFFF

LEGEND: R = Read only; W = Write only; -

n

= value after reset

Table 1-38. NMI Watchdog Period (NMIWDPRD) Register Bit Definitions (EALLOW Protected)

Bits

Name

Type

Description

15-0

NMIWDPRD

R/W

NMI Watchdog Period: This 16-bit value contains the period value at which a reset is generated
when the watchdog counter matches. At reset this value is set at the maximum. The software can
decrease the period value at initialization time.
Writing a PERIOD value that is equal to the current counter value automatically forces an NMIRS
and resets the watchdog counter. If a PERIOD value is written that is smaller than the current
counter value, the counter will continue counting until it overflows and starts counting up again from
0. After the overflow, once the COUNTER value equals the new PERIOD value, an NMIRS is forced
which resets the watchdog counter .

1.3.2.7.2 NMI Watchdog Emulation Considerations

The NMI watchdog module does not operate when trying to debug the target device (emulation suspend such as
breakpoint). The NMI watchdog module behaves as follows under various debug conditions:

CPU Suspended:

When the CPU is suspended, the NMI watchdog counter is suspended.

Run-Free Mode:

When the CPU is placed in run-free mode, the NMI watchdog counter resumes operation as normal.

Real-Time Single-Step Mode:

When the CPU is in real-time single-step mode, the NMI watchdog counter is suspended. The counter
remains suspended even within real-time interrupts.

Real-Time Run-Free Mode:

When the CPU is in real-time run-free mode, the NMI watchdog counter operates as normal.

System Control and Interrupts

92

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

«
...
90
91
92
93
94
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: Parasound Pages: 72

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

SensoTimer ST6 Duo eco!ogic

Brand: Kärcher Pages: 96

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Brand: Infineon Pages: 28

AquaLink RS All Button

Brand: Jandy Pages: 2

BoxControl Compact

Brand: elero Pages: 8

Brand: QUANT Pages: 24

Brand: HomeMatic Pages: 68

ENFORCER SLI PR-B1124-PQ

Brand: SECO-LARM Pages: 2

Brand: ULTRAFRYER Pages: 1

Brand: FASAR ELETTRONICA Pages: 2

Brand: Samson Pages: 64

Brand: Adaptec Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands