Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 49

Page: 49 / 1141

Figure 1-7. Flash Standby Wait Register (FSTDBYWAIT)

Reserved

STDBYWAIT

R-0

R/W-0x1FF

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 1-5. Flash Standby Wait Register (FSTDBYWAIT) Field Descriptions

Bit

Field

Value

Description

(1)

(2)

15-9

Reserved

Any writes to these bits must always have a value of 0.

8-0

STDBYWAIT

This register should be left in its default state.

Bank and Pump Sleep To Standby Wait Count.

111111111

511 SYSCLKOUT cycles (default)

(1)

This register is EALLOW protected. See

Section 1.5.2

for more information.

(2)

This register is protected by the Code Security Module (CSM). See

Section 1.2

for more information.

Figure 1-8. Flash Standby to Active Wait Counter Register (FACTIVEWAIT)

Reserved

ACTIVEWAIT

R-0

R/W-0x1FF

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 1-6. Flash Standby to Active Wait Counter Register (FACTIVEWAIT) Field Descriptions

Bits

Field

Value

Description

(1)

(2)

15-9 Reserved

Any writes to these bits must always have a value of 0.

8-0

ACTIVEWAIT

This register should be left in its default state.

Bank and Pump Standby To Active Wait Count:

111111111

511 SYSCLKOUT cycles (default)

(1)

This register is EALLOW protected. See

Section 1.5.2

for more information.

(2)

This register is protected by the Code Security Module (CSM). See

Section 1.2

for more information.

www.ti.com

System Control and Interrupts

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TMS320 2806 Series

Reviews:

Related manuals for TMS320 2806 Series

Brands by name

Popular brands

Texas Instruments TMS320 2806 Series, Technical Reference Manual

Search results

Summary of Contents for TMS320 2806 Series

Reviews:

Related manuals for TMS320 2806 Series

Brands by name

Popular brands