manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Technical Reference Manual

Share
Download
Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 402

Table 4-9. HRPWM Configuration (HRCNFG) Register Field Descriptions

Bit

Field

Value Description 

(1)

15-8

Reserved

Reserved

7

SWAPAB

Swap ePWM A and B Output Signals

This bit enables the swapping of the A and B signal outputs. The selection is as follows:

0

ePWMxA and ePWMxB outputs are unchanged.

1

ePWMxA signal appears on ePWMxB output and ePWMxB signal appears on ePWMxA output.

6

AUTOCONV

Auto Convert Delay Line Value

Selects whether the fractional duty cycle/period/phase in the CMPAHR/TBPRDHR/TBPHSHR register 
is automatically scaled by the MEP scale factor in the HRMSTEP register or manually scaled by 
calculations in application software. The SFO library function automatically updates the HRMSTEP 
register with the appropriate MEP scale factor.

0

Automatic HRMSTEP scaling is disabled.

1

Automatic HRMSTEP scaling is enabled.

If application software is manually scaling the fractional duty cycle, or phase (that is, software sets 
CMPAHR = (fraction(PWMduty * PWMperiod) * MEP Scale Factor)<<8 + 0x080 for duty cycle), then this 
mode must be disabled.

5

SELOUTB

EPWMxB Output Select Bit

This bit selects which signal is output on the ePWMxB channel output.

0

ePWMxB output is normal.

1

ePWMxB output is inverted version of ePWMxA signal.

4-3

HRLOAD

Shadow Mode Bit

Selects the time event that loads the CMPAHR shadow value into the active register.

00

Load on CTR = Zero: Time-base counter equal to zero (TBCTR = 0x0000)

01

Load on CTR = PRD: Time-base counter equal to period (TBCTR = TBPRD)

10

Load on either CTR = Zero or CTR = PRD

11

Reserved

2

CTLMODE

Control Mode Bits

Selects the register (CMP/TBPRD or TBPHS) that controls the MEP:

0

CMPAHR(8) or TBPRDHR(8) Register controls the edge position (that is, this is duty or period control 
mode). (Default on Reset)

1

TBPHSHR(8) Register controls the edge position (that is, this is phase control mode).

1-0

EDGMODE

Edge Mode Bits

Selects the edge of the PWM that is controlled by the micro-edge position (MEP) logic:

00

HRPWM capability is disabled (default on reset)

01

MEP control of rising edge (CMPAHR)

10

MEP control of falling edge (CMPAHR)

11

MEP control of both edges (TBPHSHR or TBPRDHR)

(1)

This register is EALLOW protected.

4.4.2 High Resolution Micro Step (HRMSTEP) Register

Figure 4-16. High Resolution Micro Step (HRMSTEP) Register

15

8

7

0

Reserved

HRMSTEP

R-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

 = value after reset

High-Resolution Pulse Width Modulator (HRPWM)

www.ti.com

402

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands