manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Technical Reference Manual

Share
Download
Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 426

5.5.5 HRCAP Counter Register (HCCOUNTER)

The HRCAP counter register (HCCOUNTER) is shown and described in the figure and table below.

Figure 5-17. HRCAP Counter Register (HCCOUNTER)

15

0

COUNTER

R-0

LEGEND: R/W = Read/Write; R = Read only; -

n

 = value after reset

Table 5-6. HRCAP Counter Register (HCCOUNTER) Field Descriptions

Bit

Field

Value

Description

15-0

COUNTER

0

16-bit capture counter

This free running counter is used to capture rising and falling edge events. The HCCOUNTER is 
incremented on every HCCAPCLK cycle. When the counter reaches 0xFFFF, it will overflow to 
0x0000 on the next cycle and generate a COUNTEROVF interrupt event.
The counter is reset to 0x0000 on every rising and falling edge event.
The counter can also be reset to 0x0000 by a system reset or by setting the HCCTL[SOFTRESET] 
bit.

NOTE:

 Because the counter is clocked from HCCAPCLK, which can be asynchronous to SYSCLK, 

CPU reads to this register should not be performed unless the clocks to the HRCAP module are 
disabled (HRCAPxENCLK = 0).

High-Resolution Capture (HRCAP) Module

www.ti.com

426

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands