Texas Instruments TMS320 2806 Series Technical Reference Manual Download Page 650 | Manualshive

Page: 650 / 1141

background image

MMOV16 MARx, mem16

Load MAR1 with 16-bit Value

Operands

MARx

CLA auxiliary register MAR0 or MAR1

mem16

16-bit destination memory accessed using one of the available
addressing modes

Opcode

LSW: mmmm mmmm mmmm mmmm (Opcode for MMOV16 MAR0, mem16)

MSW: 0111 0110 0000 addr

LSW: mmmm mmmm mmmm mmmm (Opcode for MMOV16 MAR1, mem16)

MSW: 0111 0110 0100 addr

Description

Load MAR0 or MAR1 with the 16-bit value pointed to by mem16. Refer to the pipeline
section for important information regarding this instruction.

MAR1 = [mem16];

Flags

No flags MSTF flags are affected.

Flag

TF

ZF

NF

LUF

LVF

Modified

No

No

No

No

No

Pipeline

This is a single-cycle instruction. The load of MAR0 or MAR1 will occur in the EXE phase
of the pipeline. Any post increment of MAR0 or MAR1 using indirect addressing will occur
in the D2 phase of the pipeline. Therefore the following applies when loading the auxiliary
registers:

•

I1 and I2

The two instructions following MMOV16 will use MAR0/MAR1 before the update
occurs. Thus these two instructions will use the old value of MAR0 or MAR1.

•

I3

Loading of an auxiliary register occurs in the EXE phase while updates due to post-
increment addressing occur in the D2 phase. Thus I3 cannot use the auxiliary register
or there will be a conflict. In the case of a conflict, the update due to address-mode
post increment will win send the auxiliary register will not be updated with #_X.

•

I4

Starting with the 4th instruction MAR0 or MAR1 will be the new value loaded with
MMOV16.

; Assume MAR0 is 50 and @_X is 20

MMOV16 MAR0, @_X ; Load MAR0 with the contents of X (20)

<Instruction 1> ; I1 Will use the old value of MAR0 (50)

<Instruction 2> ; I2 Will use the old value of MAR0 (50)

<Instruction 3> ; I3 Cannot use MAR0

<Instruction 4> ; I4 Will use the new value of MAR0 (20)

<Instruction 5> ; I5

....

Control Law Accelerator (CLA)

650

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

«
...
648
649
650
651
652
...
»

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

Brand: NCR Pages: 6

Brand: YOKOGAWA Pages: 150

Brand: ABB Pages: 17

Brand: Tech 21 Pages: 2

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

DIGI-STAR GT400

Brand: AGRI TRONIX Pages: 26

BACnet 4M230.8I AP

Brand: WAREMA Pages: 4

Brand: TAC Pages: 4

Brand: YASKAWA Pages: 444

Brand: Gira Pages: 7

Brand: Herth+Buss Pages: 31

Brand: SLV Pages: 12

Brand: V2 Pages: 108

Brand: Bibby Sterilin Pages: 40

Brand: Controlli Pages: 6

Brand: Stahl Pages: 15

SmartPID BBQ Easy

Brand: ARZAMAN Pages: 27

Brand: Inkbird Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands