manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Technical Reference Manual

The Texas Instruments TMS320 2806 Series offers cutting-edge technology for high-performance applications. Access the Technical Reference Manual for detailed specifications and guidelines. Download the manual for free from manualshive.com to fully utilize the capabilities of this advanced product.

Share
Download
background image

Table 16-21. Global Interrupt Flag Registers (CANGIF0/CANGIF1) Field Descriptions

Bit

Field

Value

Description

31-18

Reserved

Reserved. Reads are undefined and writes have no effect.

17

MTOF0/1

Mailbox time-out flag. This bit is not available in the SCC mode.

1

One of the mailboxes did not transmit or receive a message within the specified time frame.

0

No time out for the mailboxes occurred.

Note:

 Whether the MTOFn bit gets set in CANGIF0 or CANGIF1 depends on the value of 

MIL

n

. MTOFn gets cleared when TOSn is cleared. The TOSn bit will be cleared upon (eventual) 

successful transmission/reception.

16

TCOF0/1

Time stamp counter overflow flag.

1

The MSB of the time stamp counter has changed from 0 to 1.

0

The MSB of the time stamp counter is 0. That is, it has not changed from 0 to 1.

15

GMIF0/1

Global mailbox interrupt flag. This bit is set only when the corresponding mailbox interrupt mask bit 
in the CANMIM register is set.

1

One of the mailboxes transmitted or received a message successfully.

0

No message has been transmitted or received.

14

AAIF0/1

Abort-acknowledge interrupt flag

1

A send transmission request has been aborted.

0

No transmission has been aborted.

Note:

 The AAIFn bit is cleared by clearing the set AAn bit.

13

WDIF0/WDIF1

Write-denied interrupt flag

1

The CPU write access to a mailbox was not successful. The WDIF interrupt is asserted when the 
identifier field of a mailbox is written to, while it is enabled. Before writing to the MSGID field of a 
MBX, it should be disabled. If you try this operation when the MBX is still enabled, the WDIF bit will 
be set and a CAN interrupt asserted.

0

The CPU write access to the mailbox was successful.

12

WUIF0/WUIF1

Wake-up interrupt flag

1

During local power down, this flag indicates that the module has left sleep mode.

0

The module is still in sleep mode or normal operation

11

RMLIF0/1

Receive-message-lost interrupt flag

1

At least for one of the receive mailboxes, an overflow condition has occurred and the 
corresponding bit in the MILn register is cleared.

0

No message has been lost.

Note:

 The RMLIFn bit is cleared by clearing the set RMPn bit.

10

BOIF0/BOIF1

Bus off interrupt flag

1

The CAN module has entered bus-off mode.

0

The CAN module is still in bus-on mode.

9

EPIF0/EPIF1

Error passive interrupt flag

1

The CAN module has entered error-passive mode.

0

The CAN module is not in error-passive mode.

8

WLIF0/WLIF1

Warning level interrupt flag

1

At least one of the error counters has reached the warning level.

0

None of the error counters has reached the warning level.

7-5

Reserved

Reads are undefined and writes have no effect.

4-0

MIV0.4:0/MIV1.4:0

Mailbox interrupt vector. Only bits 3:0 are available in SCC mode.

This vector indicates the number of the mailbox that set the global mailbox interrupt flag. It keeps 
that vector until the appropriate MIFn bit is cleared or when a higher priority mailbox interrupt 
occurred. Then the highest interrupt vector is displayed, with mailbox 31 having the highest priority. 
In the SCC mode, mailbox 15 has the highest priority. Mailboxes 16 to 31 are not recognized.

If no flag is set in the TA/RMP register and GMIF1 or GMIF0 also cleared, this value is undefined.

Controller Area Network (CAN)

www.ti.com

1042

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320 2806 Series

ABB ACS355 series Quick Start Up Manual preview
ACS355 series
Brand: ABB Pages: 139
ABB ACH400 Series Retrofit Manual preview
ACH400 Series
Brand: ABB Pages: 28
ABB TZIDC-110 Operating Instructions Manual preview
TZIDC-110
Brand: ABB Pages: 59
2M Technology 2MTHFR-2M Quick Manual preview
2MTHFR-2M
Brand: 2M Technology Pages: 17
2iB SC10 Quick Start Manual preview
SC10
Brand: 2iB Pages: 5
Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
Magnescale LY71 Manual preview
LY71
Brand: Magnescale Pages: 3
Securi-Prod LK190 Installation Manual preview
LK190
Brand: Securi-Prod Pages: 3
NOCO Genius CURTIS DC Series Installation Instruction preview
CURTIS DC Series
Brand: NOCO Genius Pages: 2
Xylem Aquavar AB2 Quick Start Manual preview
Aquavar AB2
Brand: Xylem Pages: 2
A10 Networks Harmony 2000 Quick Start Manual preview
Harmony 2000
Brand: A10 Networks Pages: 2
Congatec SMARC conga-SMX8-X Quick Start Manual preview
SMARC conga-SMX8-X
Brand: Congatec Pages: 8
MT-Propeller P-8S Series Operation And Installation Manual preview
P-8S Series
Brand: MT-Propeller Pages: 16
Zander Aachen ZX09 Series Operating Manual preview
ZX09 Series
Brand: Zander Aachen Pages: 75
rotork Bifold EHPC210 Firmware Manual preview
Bifold EHPC210
Brand: rotork Pages: 22
KORINS EPIP-40 /30A(I) Instruction Manual preview
EPIP-40 /30A(I)
Brand: KORINS Pages: 3
salmson EC-Drain 2x4,0 Installation And Starting Instructions preview
EC-Drain 2x4,0
Brand: salmson Pages: 37
G-Scale Graphics RailBoss 4 Basic Operation And Installation Manual preview
RailBoss 4 Basic
Brand: G-Scale Graphics Pages: 22

Brands by name

Popular brands

Load more brands