manualshive.com logo in svg

Texas Instruments TM4C1294NCPDT, Datasheet

Share
Download
Texas Instruments TM4C1294NCPDT Datasheet Download Page 1569

Description

Reset

Type

Name

Bit/Field

Start or Stop Transmission Command

When this bit is set, transmission is placed in the running state. The
DMA attempts to acquire the descriptor from the Transmit Descriptor
List. Descriptor acquisition is attempted from the current position in the
list, which is the Transmit List Base Address set by

Transmit Descriptor

List Address (EMACTXDLADDR)

register, or from the position retained

when transmission was stopped previously.

If the DMA does not own the current descriptor, transmission enters the
suspended state and bit[2] (Transmit Buffer Unavailable,

TU

) of the

MAC

DMA Raw Interrupt Status Register (EMACDMARIS)

is set. The Start

Transmission command is effective only when transmission is stopped.
If the command is issued before setting

EMACTXDLADDR

, then the

DMA behavior is unpredictable.

When this bit is cleared, the transmission process is placed in the
Stopped state after completing the transmission of the current frame.
The Next Descriptor position in the Transmit List is saved, and it
becomes the current position when transmission is restarted. To change
the list address, you need to program

EMACTXDLADDR

with a new

value when this bit is reset. The new value is considered when this bit
is set again. The stop transmission command is effective only when the
transmission of the current frame is complete or the transmission is in
the Suspended state.

Description

Value

Transmission process is placed in the stopped state after
completing the transmission of the current frame. The Next
Descriptor position in the Transmit List is saved, and it becomes
the current position when transmission is restarted.

0

Transmission is placed in the running state, and the DMA checks
the transmit list at the current position for a frame to be
transmitted.

1

0x0

RW

ST

13

Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.

0x0

RO

reserved

12:8

Forward Error Frames

When this bit is reset, the RX FIFO drops frames with error status (CRC
error, collision error, MII_ER, giant frame, watchdog timeout, or overflow).
However, if the start byte (write) pointer of a frame is already transferred
to the RX controller side (in Threshold mode), then the frame is not
dropped.

When the

FEF

bit is set, all frames except runt error frames are

forwarded to the DMA. If Bit 25, Receive Store and Forward (

RSF

), is

set and the RX FIFO overflows when a partial frame is written, then the
frame is dropped irrespective of the

FEF

bit setting. However, if the

RSF

is reset and the RX FIFO overflows when a partial frame is written, then
a partial frame may be forwarded to the DMA.

Description

Value

The Receive FIFO drops frames with error status

0

All frames except runt error frames are forwarded to the DMA.

1

0x0

RW

FEF

7

1569

June 18, 2014

Texas Instruments-Production Data

Tiva

™

TM4C1294NCPDT Microcontroller

Summary of Contents for TM4C1294NCPDT



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands