manualshive.com logo in svg

Texas Instruments AM335 Series, Technical Reference Manual

The Texas Instruments AM335 Series is a high-performance microprocessor family. To conveniently get started with this versatile product, you can access the free Quick Start Manual on our website. Download this comprehensive manual to explore the product's features, functions, and begin your journey with the AM335 Series.

Share
Download
background image

www.ti.com

Functional Description

26.1.7.2 XIP Memory

The ROM Code can boot directly from XIP devices. A typical XIP device is a NOR flash memory. Support
for XIP devices is performed under the following assumptions:

•

Uses GPMC as the communication interface

•

Up to 1Gbit (128Mbytes) memories can be connected

•

Both x8 and x16 data bus width

•

Asynchronous protocol

•

Supports address/data multiplexed mode and non-muxed mode

•

GPMC clock is 50-MHz

•

Device connected to CS0 mapped to address 0x08000000.

•

Wait pin signal WAIT0 monitored depending on the SYSBOOT pin configuration (XIP / XIP w/ WAIT).

•

Flexible muxing options for gpmc_a0-gpmc_a11 for non-muxed XIP devices

Depending on the SYSBOOT pins, the GPMC is configured to use the WAIT signal connected on the
WAIT0 pin or not. Wait pin polarity is set to stall accessing memory when the WAIT0 pin is low. The wait
monitoring is intended to be used with memories which require long time for initialization after reset or
need to pause while reading data. The boot procedure from XIP device can be described as such:

•

Configure GPMC for XIP device access.

•

Set the image location to 0x08000000.

•

Verify if bootable image is present at the image location.

•

If the image has been found, start the execution.

•

If the image has not been found, return from XIP booting to the main booting loop.

26.1.7.2.1 XIP Initialization and Detection

•

GPMC initialization

Figure 26-9

and

Table 26-8

describe the GPMC timing settings set for XIP boot and other address-data

accessible devices.

4115

SPRUH73H – October 2011 – Revised April 2013

Initialization

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

Summary of Contents for AM335 Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM335 Series

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Brand: 3Com Pages: 8
Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
IOtech ADAC/5500MF Installation Manual preview
ADAC/5500MF
Brand: IOtech Pages: 16
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
Advantech MIC-730AI User Manual preview
MIC-730AI
Brand: Advantech Pages: 36
Omron ACCURAX G5 - Quick Start Manual preview
ACCURAX G5 -
Brand: Omron Pages: 13
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
Atmel STK501 Specification Sheet preview
STK501
Brand: Atmel Pages: 2
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Brand: ekwb Pages: 3
Alphacool EISBAER PRO Quick Start Manual preview
EISBAER PRO
Brand: Alphacool Pages: 9

Brands by name

Popular brands

Load more brands