Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 9

Page: 9 / 327

Contents

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

5.4.1

Release parking brake ........................................................................................................ 100

5.4.2

Apply parking brake............................................................................................................. 101

5.5

Brake system ........................................................................................................................... 101

5.6

Lift / Lower supporting leg ....................................................................................................... 102

5.6.1

Lift mechanical supporting leg to transport position ............................................................ 103

5.6.2

Lower mechanical supporting leg to support position ......................................................... 103

5.7

Adjust length of propeller shaft to tractor ................................................................................ 104

5.8

Adjust mounting height of folding drawbar .............................................................................. 105

5.9

Pick-up ..................................................................................................................................... 107

5.9.1

Set operating height ............................................................................................................ 107

5.9.2

Set additional guide wheels ................................................................................................ 108

5.10

Set cutting length ..................................................................................................................... 109

5.11

Mount control set on the tractor............................................................................................... 109

5.11.1

Mount ISOBUS control set on the tractor ............................................................................ 109

5.12

Hitch machine .......................................................................................................................... 110

5.12.1

Couple drawgear ................................................................................................................. 111

5.12.1.1

Tow-hook (hitch hook) and drawbar lug (hitch ring)........................................................ 111

5.12.1.2

Draw pin (Piton-Fix) and drawbar lug (hitch ring) ........................................................... 112

5.12.1.3

Ball-type coupling and shell ............................................................................................ 112

5.12.2

Connect hydraulic hose pipes ............................................................................................. 114

5.12.2.1

Open hydraulic system .................................................................................................... 114

5.12.2.2

Load-sensing mode ......................................................................................................... 115

5.12.3

Connect brake system......................................................................................................... 115

5.12.3.1

Connect dual-line service brake system ......................................................................... 116

5.12.3.2

Connect hydraulic brake system ..................................................................................... 116

5.12.3.3

Connect emergency brake valve .................................................................................... 117

5.12.4

Couple propeller shaft ......................................................................................................... 118

5.12.5

Couple forced steering axle ................................................................................................ 118

5.13

Unhitch machine ...................................................................................................................... 121

5.13.1

Uncouple drawgear ............................................................................................................. 121

5.13.1.1

Tow-hook (hitch hook) and drawbar lug (hitch ring)........................................................ 121

5.13.1.2

Draw pin (Piton-Fix) and drawbar lug (hitch ring) ........................................................... 122

5.13.1.3

Ball-type coupling and shell ............................................................................................ 122

5.13.2

Disconnect hydraulic hose pipes ......................................................................................... 122

5.13.3

Disconnect brake system .................................................................................................... 123

5.13.3.1

Disconnect dual-line service brake system ..................................................................... 123

5.13.3.2

Disconnect hydraulic brake system ................................................................................ 123

5.13.3.3

Disconnect hydraulic brake system with emergency brake valve ................................... 124

5.13.4

Uncouple propeller shaft ..................................................................................................... 125

5.14

Manoeuvre unhitched machine by means of a manoeuvring vehicle ..................................... 126

5.15

External operation for folding drawbar .................................................................................... 127

5.16

Mount extension sections, ropes and superstructure tarpaulin ............................................... 127

5.17

Superstructure tarpaulin with rewinding and securing mechanism ......................................... 130

5.17.1

Unwind superstructure tarpaulin ......................................................................................... 130

5.17.2

Rewind superstructure tarpaulin ......................................................................................... 131

5.18

Cover conveyor duct ............................................................................................................... 132

Operation ........................................................................................................ 133

6.1

ISOBUS control / Field Operator 120 ...................................................................................... 134

6.1.1

Design of ISOBUS control ................................................................................................... 134

6.1.2

Display information in Working menu .................................................................................. 136

6.1.3

Functions of the ISOBUS control ........................................................................................ 137

6.1.3.1

Switch control set on/off .................................................................................................. 137

6.1.3.2

Switch road travel mode on ............................................................................................. 137

6.1.3.3

Switch road travel mode off ............................................................................................. 139

6.1.3.4

Switch discharge mode A I on......................................................................................... 140

6.1.3.5

Switch Discharge mode A II on (machine without beaters) ............................................ 141

6.1.3.6

Switch discharge mode A II on (machine equipped with beaters) .................................. 141

6.1.3.7

Switch automatic charging system on/off ........................................................................ 142

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands

Strautmann Giga-Vitesse CFS 3602, Operating Instructions Manual

Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands