Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 65 | Manualshive

Page: 65 / 327

background image

Safety instructions

65

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

3.4.1

Lock tailgate

The tailgate can be locked via the stop-cock to secure it against accidental lifting and lowering. The
stop-cock is positioned on the right-hand side of the tailgate.

The table shows the meaning of the stop-cock positions.

I - Stop-cock open

0 - Stop-cock closed

Fig. 37

Fig. 38

Stop-cock

Tailgate

Activity

0 - closed

Lifted and locked

Trouble-shooting, cleaning, service

and maintenance work

I - Open

Not locked

Lifting and lowering possible

Charging and discharging

«
...
63
64
65
66
67
...
»

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews:

No comments

Related manuals for Giga-Vitesse CFS 3602

Brand: ABB Pages: 36

Brand: ABB Pages: 40

Brand: FagronLab Pages: 16

Brand: Eastern Jungle Gym Pages: 17

Brand: Vahle Pages: 96

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: Walimex Pro Pages: 44

Brand: Otto Bock Pages: 72

Brand: Meritor Pages: 65

Brand: Nakayama Pages: 19

Brand: WAGNER Pages: 31

Brand: Simplicity Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands