manualshive.com logo in svg

Strautmann Giga-Vitesse CFS 3602, Operating Instructions Manual, Page: 24 / 327

Share
Download
Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 24

Product description

 

 

 

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO   03.18 

24 

 

(1) 

Feed line with hose coupling (red) 

(2) 

Brake line with hose coupling (yellow) 

(3) 

Blank connection for brake line 

(4) 

Trailer brake valve 

(5) 

ALB regulator (mechanical) 

(6) 

Release valve 

(7) 

Operating element for release valve (can 
only be actuated in uncoupled condition): 

• 

Push in as far as it will go and the service 
brake system releases, e.g. for 
manoeuvring the unhitched machine 

• 

Pull out as far as it will go and the machine 
is braked again by means of the system 
pressure coming from the air reservoir 

(8) 

Diaphragm brake cylinder 

(9) 

Compressed-air reservoir 

(10)  Drain valve 

(11)  Test connection in front of ALB regulator 

(12)  Test connection behind ALB regulator 

(13)  Test connection, diaphragm brake cylinder 

(14)  Test connection, compressed-air reservoir 

(15)  Parking brake 

 

 

 

Fig. 6 

 

 

 

 

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews:

No comments